manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 83 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 83

A-8

   Compaq ProLiant ML330 Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

g-appa Regulatory Compliance Notices.doc  

Last Saved On: 

1/17/00 2:59 PM

Power Cords

If you were not provided with a power cord for your computer, you should
purchase a power cord that is approved for use in your country.

The power cord must be rated for the product and for the voltage and current
marked on the product’s electrical ratings label. The voltage and current rating
of the cord should be greater than the voltage and current rating marked on the
product. In addition, the diameter of the wire must be a minimum of 1.00 mm²
or 18AWG, and the length of the cord must be between 1.8 m (6 feet) and
3.6 m (12 feet). If you have questions about the type of power cord to use,
contact your Compaq authorized service provider.

A power cord should be routed so that it is not likely to be walked on or
pinched by items placed upon it or against it. Particular attention should be
paid to the plug, electrical outlet, and the point where the cord exits from the
product.

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments