manualshive.com logo in svg

Compaq ML330 - ProLiant - G3, Setup And Installation Manual, Page: 29 / 99

Share
Download
Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 29

Overview of Server Installation  

2-7

Compaq Confidential – Need to Know Required

Writer:

 Donna Hollas  

Project:

 Compaq ProLiant ML330 Setup and Installation Guide  

Comments:

 

Part Number:

 173868-001  

File Name: 

c-ch2 Overview of Server Installation.doc  

Last Saved On: 

1/17/00 1:37 PM

Configuring the Server

The BIOS Setup Utility can be used to configure the server and options. To
invoke the setup utility, press the F10

F10

F10

F10 key when prompted during the startup

process.

The SmartStart and Support Software CD contains the ROMPaq and updated
drivers, and assists with the operating system installation. To use the
SmartStart and Support Software CD:

 

1.

 

Locate the SmartStart and Support Software CD in the Server Setup and
Management pack.

 

2.

 

With your server powered up, press the CD-ROM drive eject button.

 

3.

 

Insert the SmartStart and Support Software CD in the CD-ROM drive
with the labeled side up. Handle the CD by its edges, not by the flat
surfaces of the disc.

Figure 2-3.  Inserting the CD

 

4.

 

When the busy indicator turns green, the SmartStart sequence begins.
Refer to the SmartStart and Support Software CD for more information.

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments