Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 86 | Manualshive

Page: 86 / 99

Compaq ML330 - ProLiant - G3 Setup And Installation Manual Download Page 86

Compaq Confidential – Need to Know Required

Writer:

Donna Hollas

Project:

Compaq ProLiant ML330 Setup and Installation Guide

Comments:

Part Number:

173868-001

File Name:

i-appc Switches and Jumpers.doc

Last Saved On:

1/17/00 3:14 PM

Appendix

C

Switches and Jumpers

When you add or remove a component or change a security feature, you must
reconfigure the server to recognize these changes. If the system configuration
is incorrect, your server may not work properly and you may receive error
messages on the screen. Setting the system board switches is part of the
reconfiguration process, along with running the BIOS Setup Utility.

Switch Settings

The ProLiant ML330 system board has two switches that are used to set
configuration and processor speed options on your server. The Server Feature
Board has a switch, that is used to set configuration options on the Server
Feature Board. Refer to the access panel labels, to the Quick Start Poster, or to
the tables below for settings.

«
...
84
85
86
87
88
...
»

Summary of Contents for ML330 - ProLiant - G3




































































































Reviews:

No comments