manualshive.com logo in svg

Compaq D315 - Desktop PC, Troubleshooting Manual, Page: 57 / 76

Share
Download
Compaq D315 - Desktop PC Troubleshooting Manual Download Page 57

Troubleshooting Guide

A–11

Post Error Messages

1720-SMART 
Hard Drive 
Detects Imminent 
Failure

None

Hard drive is about 
to fail. (Some hard 
drives have a firmware 
patch that will fix an 
erroneous error 
message.)

1. Determine if hard drive 

is giving correct error 
message. Run the Drive 
Protection System test if 
available.

2. Apply firmware patch 

if applicable. (See 

www.compaq.com/
support/techpubs/
customer_advisories.

)

3. Back up contents and 

replace hard drive.

1782-Disk 
Controller Failure

None

Hard drive circuitry 
error.

1. Run Computer Setup.

2. Clear CMOS. (See 

Appendix B, “Password 
Security and Resetting 
CMOS.”)

3. Check cable seating/jumper 

settings.

4. Run hard drive diagnostics.

5. Disconnect additional 

drives.

6. Run the Drive Protection 

System test if available.

7. Replace the hard drive.

8. Replace the system board.

*L = Long, S = Short

Numeric Codes and Text Messages 

(Continued)

Code/Message

Beeps

Probable Cause

Recommended Action

292974-002.book Page 11 Tuesday, July 9, 2002 5:46 PM

Summary of Contents for D315 - Desktop PC













































































Reviews:

No comments