manualshive.com logo in svg

Compaq D315 - Desktop PC, Troubleshooting Manual, Page: 41 / 76

Share
Download
Compaq D315 - Desktop PC Troubleshooting Manual Download Page 41

Troubleshooting Guide

2–27

Troubleshooting Without Diagnostics

Solving Processor Problems

If you encounter processor problems, a common cause and solution 
are listed in the following table.

Solving Memory Problems

If you encounter memory problems, some common causes and 
solutions are listed in the following table.

Ä

CAUTION: 

For those systems that support ECC memory, Compaq does 

not support mixing ECC and non-ECC memory. Otherwise, the 

Num Lock

 LED on non-USB keyboards will blink continuously, and the 

system will not boot the operating system. In addition, if a speaker 
is installed in the system, there will be a short beep followed by 2 long 
beeps.

✎

See the “Interpreting the Diagnostic Lights” section of the 

Getting 

Started

 guide to identify other possible memory problems.

Solving Processor Problems

Problem

Cause

Solution

Poor performance is 
experienced.

Processor is hot.

1. Make sure the airflow to the 

computer is not blocked.

2. Make sure the fans are 

connected and working 
properly (some fans only 
operate when needed).

3. Make sure the processor 

heatsink is installed properly.

292974-002.book Page 27 Tuesday, July 9, 2002 5:46 PM

Summary of Contents for D315 - Desktop PC













































































Reviews:

No comments