manualshive.com logo in svg

CITROEN Berlingo 2003, Handbook

Share
Download
CITROEN Berlingo 2003 Handbook Download Page 427

423

BRAKES

CHECKING AND ADJUSTING THE LOAD-SENSITIVE BRAKE COMPENSATOR

Adjusting the load-sensitive brake compensator

- Untighten the screw

(1).

- Move the spring rod.
- Decrease the length of the spring to increase the pressure.
- Increase the length of the spring to decrease the pressure.
- Tighten the screw

(1) 

to

1,2 ± 0,25 m.daN.

- Check the brake pressure.

After the operation : 

- Remove the checking tool

[1].

- Bleed the braking circuit (see corresponding operation).
- Carry out a road test.

XSARA PICASSO - All Types

B3FP13VC

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands