manualshive.com logo in svg

CITROEN Berlingo 2003, Handbook

Share
Download
CITROEN Berlingo 2003 Handbook Download Page 126

122

ENGINE

XSARA - XSARA PICASSO

AUXILIARY EQUIPMENT DRIVE BELT

Engines : RHY - RHZ

With air conditioning

B1BP1YLD

Tools

[1] 

Belt tension adjusting square

: 

(-).0188 J2

[2]

Pige 

Ø 4 mm

:

(-).0188.Q1

[3]

Pige 

Ø 2 mm

:

(-).0188.Q2

[4] 

Dynamic tensioner compression lever

:

(-).0188.Z

REMOVAL

Re-use of belt
WARNING : Mark the direction the belt was fitted in case of re-use of the same belt.

- Compress the tensioner roller 

(7)

by moving it at 

« c »

(in anti-clockwise direction),

tool 

[4]

.

- Hold the tensioner roller 

(7)

compressed and remove the belt.

No re-use of belt

- Compress the tensioner roller 

(7)

by moving it at 

« c »

(in anti-clockwise direction), tool 

[4]

.

- Peg using tool 

[2]

, at 

« d »

.

- Loosen the screw 

(6)

.

- Bring the eccentric roller

(5)

towards the rear.

- Tighten the screw 

(6)

by hand.

- Remove the belt.

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands