CITROEN Berlingo 2003 Handbook Download Page 256

Page: 256 / 482

252

INJECTION

FITTING DELPHI DIESEL INJECTORS

Engine : WJY

B1DP158C

B1HP12VC

B1HP0YGC

Fitting an injector

The copper seal

(1)

and the fire

seal washer

(3)

are to be replaced

each time they are removed.

NOTE :

Fitting parts of different

makes is

PROHIBITED

WARNING :

Ensure that the

fire seal washer

(3)

is fitted the

right way round.

Tighten the injector holder

on the cylinder head to :

9 m.daN

[1]

Tool to remove/refit injectors

(2)

7007-T

[2]

7008-T.A Tool kit 4123-T

(3)

Tighten lightly to prevent any distortion.

XSARA

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Search results

Summary of Contents for Berlingo 2003

Reviews:

Brands by name

Popular brands

CITROEN Berlingo 2003, Handbook

Search results

Summary of Contents for Berlingo 2003

Reviews:

Brands by name

Popular brands