manualshive.com logo in svg

CITROEN Berlingo 2003, Handbook

Share
Download
CITROEN Berlingo 2003 Handbook Download Page 202

198

ENGINE

The new fitting discontinues the following components : 

Camshaft hub.
Cylinder reference sensor target.

Repair – Accessories drive pulley

Remove – Refit

WARNING : 

Peg the camshaft and the crankshaft before ever removing the

accessories drive pulley (the pegging prevents any offsetting of the camshaft).

If necessary, apply a paint spot to mark the accessories drive pulley being
replaced.

Replacement parts.

The Replacement Parts service markets the old as well as the new components.

SPECIAL FEATURES: CHECKING AND SETTING THE VALVE TIMING

Engines : RHY - RHZ         N° RPO 9128  

# 

NEW FITTING : RPO 9128   

# 

(continued)

B1EP177D

XSARA - XSARA PICASSO

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands