manualshive.com logo in svg

CITROEN Berlingo 2003, Handbook

Share
Download
CITROEN Berlingo 2003 Handbook Download Page 235

231

INJECTION

PROHIBITED OPERATIONS: SIEMENS HDI DIRECT INJECTION SYSTEM

Engines : 8HX - 8HW

Cleaning.

- The use of high pressure cleaners is prohibited.
- Do not use compressed air.

Fuel supply circuit.

- Required fuel : diesel.

Electric circuit.

- Swapping injection ECUs between two vehicles will render it impossible to start either vehicle.
- It is forbidden to supply a diesel injector with 12 volts.

High pressure fuel pump.

Do not separate the following components from the high pressure fuel pump

(5)

:

- Sealing ring

(a)

(no replacement parts).

- High pressure outlet connector 

(b)

(will cause a malfunction).

PS : HDi = High pressure Diesel injection

B1HP1K9C

C3

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands