manualshive.com logo in svg

CITROEN Berlingo 2003, Handbook

Share
Download
CITROEN Berlingo 2003 Handbook Download Page 231

227

INJECTION

SAXO

ADJUSTING THE MECHANICAL CONTROLS OF THE BOSCH INJECTION PUMP

ADJUSTING THE FAST IDLE SPEED.

- Bring the lever 

(3)

into contact with the screw

(2)

.

- Use the screw 

(2)

to obtain the fast idle speed :

1100 ± 100 rpm

.

Engine cold.

- Ensure that the lever

(3)

is up against the screw stop 

(2)

.

- If not, slightly tension the cable

(4)

using the cable clamp 

(1)

.

- Finish tensioning with the sheath tensioner 

(5)

.

Engine hot.

- Ensure that the cable

(4)

is slack.

- Check the operation of the thermostatic sensor on the coolant outlet housing : there should be a minimum 

6 mm

cable travel between a cold and a hot engine.

- If not, replace the thermostatic sensor. Tighten to

2.5 m.daN

.

B1HP0HQC

Engine : VJX

B1HP0HUC

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands