manualshive.com logo in svg

CITROEN Berlingo 2003, Handbook

Share
Download
CITROEN Berlingo 2003 Handbook Download Page 194

190

ENGINE

CHECKING AND SETTING THE VALVE TIMING

Engine : WJY

Setting the valve timing  (continued)

Rotate the crankshaft by

8 turns

(direction of rotation).

Peg :

- The hub

(1)

, using tool 

[1]

.

- The pinion 

(2)

, using tool 

[2]

.

- The flywheel, using the tool 

[3]

.

Loosen :

- The screws 

(4) 

and 

(5)

.

- The roller 

(9)

.

- Retighten screws 

(4)

and 

(5)

by hand.

- Fit the tool

[7]

to the belt strap at

"a"

.

- Turn the roller

(9)

(anti-clockwise direction) using tool

[6]

, to obtain :

42 ± 2 SEEM units

.

B1EP134C

B1CP045C

B1EP133C

XSARA

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands