CITROEN Berlingo 2003 Handbook Download Page 239

Page: 239 / 482

235

INJECTION

CHECKS : LOW PRESSURE FUEL SUPPLY CIRCUIT

Engines : 8HX - 8HW

TOOLS

[1] Ø 10 mm

low pressure connector

: 4215-T.

[2]

Pressure gauge for testing boost pressure

: 4073-T.A

Tool kit 4073-T

IMPERATIVE : Respect the safety and cleanliness specific to high pressure diesel
injection engines.

Link tools

[1]

and

[2]

in series between the fuel high pressure pump and the fuel filter.

ESSENTIAL : Check that the tool [2] is clean.

Check the negative pressure according to the table below:

Vacuum

Observations

10 ±5 cmHg

Engine driven by the starter motor

20 ±5 cmHg

60 ±5 cmHg

Engine running under full load

Supply circuit obstructed (full tank

strainer, piping, fuel filter).

B1BP2NWC

Summary of Contents for Berlingo 2003



































































































































































































































































































































































































































































































Search results

Summary of Contents for Berlingo 2003

Reviews:

Brands by name

Popular brands

CITROEN Berlingo 2003, Handbook

Search results

Summary of Contents for Berlingo 2003

Reviews:

Brands by name

Popular brands