S e n d f e e d b a c k t o n x 5 0 0 0 - d o c f e e d b a c k @ c i s c o . c o m
25-3
Cisco Nexus 5000 Series Switch CLI Software Configuration Guide
OL-16597-01
Chapter 25 Configuring System Message Logging
Configuring System Message Logging
The following example shows how to configure a switch to log messages:
switch#
configure terminal
switch(config)#
logging console 3
switch(config)#
no logging console
switch(config)#
show logging console
switch(config)#
logging monitor 3
switch(config)#
no logging monitor
switch(config)#
show logging monitor
switch(config)#
copy running-config startup-config
Configuring System Message Logging to a File
You can configure the switch to log system messages to a file. By default, system messages are logged
to the file log:messages.
For information about displaying and clearing log files, see the
“Displaying and Clearing Log Files”
section on page 25-8
.
To configure the switch to log system messages to a file, perform this task:
Command
Purpose
Step 1
switch#
configure terminal
Enters configuration mode.
Step 2
switch(config)#
logging console
[
severity-level
]
Enables the switch to log messages to the console
session based on a specified severity level or higher.
Severity levels, which can range from 0 to 7, are listed
in
Table 25-1
. If the severity level is not specified, the
default of 2 is used.
switch(config)#
no logging console
[
severity-level
]
Disables the switch’s ability to log messages to the
console.
Step 3
switch(config)#
show logging console
(Optional) Displays the console logging
configuration.
Step 4
switch(config)#
logging monitor
[
severity-level
]
Enables the switch to log messages to the monitor
based on a specified severity level or higher. The
configuration applies to Telnet and SSH sessions.
Severity levels, which can range from 0 to 7, are listed
in
Table 25-1
. If the severity level is not specified, the
default of 2 is used.
switch(config)#
no logging monitor
[
severity-level
]
Disables logging messages to telnet and SSH
sessions.
Step 5
switch(config)#
show logging monitor
(Optional) Displays the monitor logging
configuration.
Step 6
switch(config)#
copy running-config
startup-config
(Optional) Copies the running configuration to the
startup configuration.
Summary of Contents for N5010P-N2K-BE
