S e n d f e e d b a c k t o n x 5 0 0 0 - d o c f e e d b a c k @ c i s c o . c o m
7-9
Cisco Nexus 5000 Series Switch CLI Software Configuration Guide
OL-16597-01
Chapter 7 Configuring Private VLANs
Configuring a Private VLAN
Note
We recommend that you enable BPDU Guard on all interfaces configured as a host ports. See
Chapter 10, “Configuring STP Extensions”
for information on configuring BPDU Guard.
Ensure that the private VLAN feature is enabled.
To configure an interface as a private VLAN host port, perform this task:
This example shows how to configure the Ethernet port 1/12 as a host port for a private VLAN and
associate it to primary VLAN 5 and secondary VLAN 101:
switch#
configure terminal
switch(config)#
interface
ethernet 1/12
switch(config-if)#
switchport
mode
private-vlan host
switch(config-if)#
switchport
private-vlan host-association 5 101
To remove the private VLAN association from an interface, perform this task:
Configuring an Interface as a Private VLAN Promiscuous Port
You can configure an interface as a private VLAN promiscuous port, and then you can associate that
promiscuous port with the primary and secondary VLANs.
Ensure that the private VLAN feature is enabled.
To configure an interface as a private VLAN promiscuous port, perform this task:
Command
Purpose
Step 1
switch#
configure terminal
Enters configuration mode.
Step 2
switch(config)#
interface
type
slot
/
port
Selects the port to configure as a private VLAN host
port. The interface can be either a physical Ethernet
port.
Step 3
switch(config-if)#
switchport mode
private-vlan host
Configures the port as a host port for a private VLAN.
Step 4
switch(config-if)#
switchport
private-vlan host-association
{
primary-vlan-id
} {
secondary-vlan-id
}
Associates the port with the primary and secondary
VLANs of a private VLAN. The secondary VLAN
can be either an isolated or community VLAN.
Command
Purpose
switch(config-if)#
no switchport
private-vlan host-association
Removes the private VLAN association from the port.
Command
Purpose
Step 1
switch#
configure terminal
Enters configuration mode.
Step 2
switch(config)#
interface
type
slot
/
port
Selects the port to configure as a private VLAN
promiscuous port. A physical interface is required.
Summary of Contents for N5010P-N2K-BE
