manualshive.com logo in svg

Cisco 3845 - Security Bundle Router, Software Manual

The Cisco 3845 - Security Bundle Router offers top-notch network security features. Ensure optimum performance with the comprehensive Software Manual, available for free download at manualshive.com. Find detailed instructions and insights to maximize the potential of your Cisco 3845 and safeguard your network from potential threats.

Share
Download
background image

 

29-17

Cisco ME 3800X and 3600X Switch Software Configuration Guide

OL-23400-01

Chapter 29      Configuring IP Unicast Routing

Configuring RIP

Use the no ip routing global configuration command to disable routing.

This example shows how to enable IP routing using RIP as the routing protocol:

Switch# 

configure terminal 

Enter configuration commands, one per line.  End with CNTL/Z.

Switch(config)# 

ip routing 

Switch(config)# 

router rip

 

Switch(config-router)# 

network 10.0.0.0 

Switch(config-router)# 

end

 

You can now set up parameters for the selected routing protocols as described in these sections:

•

Configuring RIP, page 29-17

•

Configuring OSPF, page 29-22

•

Configuring EIGRP, page 29-33

•

Configuring BGP, page 29-41

•

Configuring ISO CLNS Routing, page 29-61

•

Configuring BFD for OSPF, page 29-74

•

Configuring Protocol-Independent Features, page 29-93

 (optional)

Configuring RIP

The Routing Information Protocol (RIP) is an interior gateway protocol (IGP) used in small, 
homogeneous networks. It is a distance-vector routing protocol that uses broadcast User Datagram 
Protocol (UDP) data packets to exchange routing information. You can find detailed information about 
RIP in IP Routing Fundamentals, published by Cisco Press.

Using RIP, the switch sends routing information updates (advertisements) every 30 seconds. If a router 
does not receive an update from another router for 180 seconds or more, it marks the routes served by 
that router as unusable. If there is still no update after 240 seconds, the router removes all routing table 
entries for the non-updating router. 

RIP uses hop counts to rate the value of different routes. The hop count is the number of routers that can 
be traversed in a route. A directly connected network has a hop count of zero; a network with a hop count 
of 16 is unreachable. This small range (0 to 15) makes RIP unsuitable for large networks.

Step 3

router ip_routing_protocol 

Specify an IP routing protocol. This step might include other 
commands, such as specifying the networks to route with the 
network (RIP) router configuration command. For information on 
specific protocols, see sections later in this chapter and to the Cisco 
IOS IP Configuration Guide, Release 12.2.

Step 4

end 

Return to privileged EXEC mode.

Step 5

show running-config

Verify your entries.

Step 6

copy running-config startup-config 

(Optional) Save your entries in the configuration file.

Command

Purpose

Summary of Contents for 3845 - Security Bundle Router





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3845 - Security Bundle Router

D-Link DES-7200 User Manual preview
DES-7200
Brand: D-Link Pages: 100
D-Link DES-3226L Manual preview
DES-3226L
Brand: D-Link Pages: 134
D-Link DES-3010F Command Line Interface Manual preview
DES-3010F
Brand: D-Link Pages: 187
D-Link DES-3010F Manual preview
DES-3010F
Brand: D-Link Pages: 225
D-Link DES-1048G Manual preview
DES-1048G
Brand: D-Link Pages: 31
D-Link DES-1050G User Manual preview
DES-1050G
Brand: D-Link Pages: 35
D-Link DES-1016D - Switch Quick Install Manual preview
DES-1016D - Switch
Brand: D-Link Pages: 19
D-Link COVR-2202 User Manual preview
COVR-2202
Brand: D-Link Pages: 107
D-Link AirPlusXtremeG DI-624 Troubleshooting preview
AirPlusXtremeG DI-624
Brand: D-Link Pages: 5
D-Link DGS-1210-28P Getting Started Manual preview
DGS-1210-28P
Brand: D-Link Pages: 48
Cambium Networks PTP 820 Series Manual preview
PTP 820 Series
Brand: Cambium Networks Pages: 29
Allied Telesis AT-8000C Declaration Of Conformity preview
AT-8000C
Brand: Allied Telesis Pages: 1
AMX NXA-ENET8POE Installation Manual preview
NXA-ENET8POE
Brand: AMX Pages: 2
Abocom WR5502 User Manual preview
WR5502
Brand: Abocom Pages: 63
AirLive Ether-GSH24T v3 Quick Setup Manual preview
Ether-GSH24T v3
Brand: AirLive Pages: 2
VideoWave Adam Device User Manual preview
Adam Device
Brand: VideoWave Pages: 12
Paradyne iMarc SLV 9820-2M Installation Instructions Manual preview
iMarc SLV 9820-2M
Brand: Paradyne Pages: 24
Edimax GS-5208PLG V2 Quick Installation Manual preview
GS-5208PLG V2
Brand: Edimax Pages: 15

Brands by name

Popular brands

Load more brands