manualshive.com logo in svg

Cisco 3845 - Security Bundle Router, Software Manual

The Cisco 3845 - Security Bundle Router offers top-notch network security features. Ensure optimum performance with the comprehensive Software Manual, available for free download at manualshive.com. Find detailed instructions and insights to maximize the potential of your Cisco 3845 and safeguard your network from potential threats.

Share
Download
background image

 

27-23

Cisco ME 3800X and 3600X Switch Software Configuration Guide

OL-23400-01

Chapter 27      Configuring QoS

Understanding QoS

However, these output policy maps can contain only three unique configurations of queue limits. These 
three unique queue-limit configurations can be included in as many output policy maps as there are 
switch ports. There are no limitations on the configurations of bandwidth, priority, or shaping.

QoS Treatment for Performance-Monitoring Protocols

QoS is not configurable for Cisco IP service level agreements (IP SLA) probes or for traffic to the CPU. 
QoS treatment is set by default.

•

Cisco IP-SLAs Probes, page 27-23

•

CPU Traffic, page 27-23

Cisco IP-SLAs Probes

For information about Cisco IP service level agreements (IP SLAs), see the 

“Understanding Cisco IOS 

IP SLAs” section on page 31-1

.

The QoS treatment for IP-SLA probes exactly reflects effects that occur to the normal data traffic 
crossing the device. The generating device does not change the probe markings. It queues these probes 
based on the configured queueing policies for normal traffic. 

•

Marking

By default, the CoS marking of CFM traffic (including IP SLAs using CFM probes) is not changed. 
QoS configuration cannot change this behavior.

By default, IP traffic marking and the CoS marking of all other Layer 2 non-IP traffic is not changed. 
The QoS marking feature can change this behavior.

•

Queuing

IP SLAs traffic is queued according to its ToS or DSCP value and the output policy map configured 
on the egress target, similarly to normal traffic. QoS cannot change this behavior.

By default, all other Layer 2 non-IP traffic and all IP traffic is statically mapped to a queue on the 
egress target. 

CPU Traffic

By default, the switch assigns a separate classifier, CPU-traffic classifier, for all traffic destined to the 
CPU. For traffic from the CPU, the switch uses a default classifier for high-priority control protocol 
traffic. These protocols are considered high priority: 

•

Protocols with the PAK_PRIORITY flag set in Cisco IOS software. These include EIGHT, HSPR, 
GRD, LDP, OSPF, RIP, WCCP, BFD, CFM, SAA, CDP, ISIS, DTP, IGRP, Ethernet OAM, LACP, 
LLDP, PAgP, and STP. 

•

IP protocols with IP precedence set to 6 or 7.

All other traffic from the CPU is classified with a normal classifier.

Summary of Contents for 3845 - Security Bundle Router





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3845 - Security Bundle Router

D-Link DSL-G2562DG Quick Start Manual preview
DSL-G2562DG
Brand: D-Link Pages: 2
National Instruments NI 9871 Operating Instructions Manual preview
NI 9871
Brand: National Instruments Pages: 24
National Instruments NI 9478 Operating Instructions Manual preview
NI 9478
Brand: National Instruments Pages: 32
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 8
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
Aztech DSL1000EW(L) Speci?Cations preview
DSL1000EW(L)
Brand: Aztech Pages: 2
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
Toto Link IP04229 User Manual preview
IP04229
Brand: Toto Link Pages: 55
ZyXEL Communications NBG-460N Manual preview
NBG-460N
Brand: ZyXEL Communications Pages: 5
Eneo PNR-5304 Quick Installation Manual preview
PNR-5304
Brand: Eneo Pages: 68
EMS 2000 IDU Series User Manual preview
2000 IDU Series
Brand: EMS Pages: 52
Cabletron Systems CyberSWITCH CSX101 User'S Information Manual preview
CyberSWITCH CSX101
Brand: Cabletron Systems Pages: 72
B+B SmartWorx SPECTRE v3 LTE User Manual preview
SPECTRE v3 LTE
Brand: B+B SmartWorx Pages: 50
Cradlepoint MBR900 Quick Start Manual preview
MBR900
Brand: Cradlepoint Pages: 2
Vaisala TERMBOX-9000 User Manual preview
TERMBOX-9000
Brand: Vaisala Pages: 32
Tenda FH456 User Manual preview
FH456
Brand: Tenda Pages: 82
Tripp Lite P581-006 Specification Sheet preview
P581-006
Brand: Tripp Lite Pages: 2

Brands by name

Popular brands

Load more brands