Cisco 3825 Series Software Configuration Manual Download Page 42

Page: 42 / 358

1-32

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Chapter 1 Overview of the Cisco 3825 Mobile Wireless Edge Router

New Features in Cisco IOS Release 12.4(16)MR

UMTS-Iub(ATM0/IMA0.1): PVC matching

Peering state: OPEN

Local PVCs:

PVC(1/200): has MATCHING remote PVC.

Remote PVCs:

PVC(1/200): has MATCHING local PVC.

Lisa#show umts packet

UMTS-Iub(ATM0/IMA0): packets:

rxUMTS_count ================ 468845

txUMTS_count ================ 276847

rxUMTS_bytes ================ 22504560

txUMTS_bytes ================ 13288656

rxBackhaul_packets ========== 58216

txBackhaul_packets ========== 88884

rxBackhaul_bytes ============ 14687104

txBackhaul_bytes ============ 24824360

Last cleared 00:50:39

UMTS-Iub(ATM0/IMA0.1): packets:

rxUMTS_count ================ 126173

txUMTS_count ================ 126173

rxUMTS_bytes ================ 6056304

txUMTS_bytes ================ 6056304

rxBackhaul_packets ========== 28405

txBackhaul_packets ========== 28777

rxBackhaul_bytes ============ 6532571

txBackhaul_bytes ============ 7596968

Last cleared 00:08:08

Behavior Changes

The following behavior changes will be apparent when using this PVC Routing feature.

When the

no atm umts

command is applied to a base ATM interface, the command will

un-configure the ATM UMTS mode for all the sub-interfaces under that ATM interface.

When the

no atm umts

command is applied to an ATM sub-interface, the command will

un-configure the ATM UMTS mode only for that sub-interface.

Alarms are carried over the primary backhaul only, while the primary peering will have the alarm
information. The following is a sample output:

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Peering Information

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Local (20.20.20.21:6666) States:

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Connect State: OPEN

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Redundancy State: ACTIVE

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Version: 4

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Alarm State:

UMTS-Iub(ATM0/0/0 - ATM0/0/0): RX(NO ALARM) TX(NO ALARM)

UMTS-Iub(ATM0/0/1 - ATM0/0/1): RX(NO ALARM) TX(NO ALARM)

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Remote (20.20.20.20:6666) States:

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Version: 4

UMTS-Iub(ATM0/IMA0 - ATM0/IMA0): Alarm State:

UMTS-Iub(ATM0/0/0 - ATM0/0/0):

RX(NO ALARM) TX(NO ALARM)

UMTS-Iub(ATM0/0/1 - ATM0/0/1):

RX(NO ALARM) TX(NO ALARM)

Summary of Contents for 3825 Series







































































































































































































































































































































































Search results

Summary of Contents for 3825 Series

Reviews:

Cisco 3825 Series, Software Configuration Manual, Page: 42 / 358

Search results

Summary of Contents for 3825 Series

Reviews: