manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 261 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 261

       

A-129

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    umts-iub set dscp

umts-iub set dscp

To overwrite the interface default value defined in the 

umts-iub set dscp 

value

 

for UMTS shorthaul 

interfaces and is used to tag the backhaul packet generated from traffic from a PVC, use the 

umts-iub 

set dscp 

ATM-VC configuration command. 

umts-iub set dscp 

value

Note

Use this command when configuring PVCs of the UMTS shorthaul interfaces

Syntax Description

Defaults

There are no default settings or behaviors.

Command Modes

ATM-VC configuration

Command History

Examples

The following example shows how to configure the remote parameters:

Router(config)# 

interface ATM0/2/0

Router(config-if)# 

atm umts-iub

Router(config-if)# 

umts-iub set dscp 

value

Router(config-if-atm-vc)# 

umts-iub set dscp 

value

Related Commands

value

A number from 0 to 63 or hex value that sets the UMTS-Iub DSCP value.

Release

Modification

12.4(4)MR

This command was introduced.

Command

Description

umts-iub set dscp

 

(Interface Configuration mode)

This command sets the description value used as the interface 
default description value to tag the backhaul packet including the 
peering and data generated from the shorthaul

umts-iub set peering dscp 

This command overwrites the interface default value defined in the 

umts-iub set dscp 

value

 

and is used to tag the peering backhaul 

packet

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments