manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 242 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 242

       

A-110

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    show umts-iub pvc

show umts-iub pvc

To display the pvc mapping of the UMTS Iub interface, use the 

show umts-iub pvc 

command in 

privileged EXEC mode.

show umts-iub pvc

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History

Examples

The following is an example of the output generated by this command.

Router# show umts pvc

UMTS(ATM0/0/1): VCD info

VCD Mapping:

  Local Index(1) <--> Local VCD(1) <--> Remote Index(1)

Local VCDs (not sent):

Local VCDs (sent):

  Index(1), VPI/VCI(2/100), Encap(6), SC(0), Peak(1920), Avg/Min(0), Burst Cells(0)

Remote VCDs:

  Index(1), VPI/VCI(2/100), Encap(6), SC(0), Peak(1920), Avg/Min(0), Burst Cells(0)

Release

Modification

12.4(2)MR

This command was introduced.

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments