manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 235 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 235

       

A-103

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    show umts-iub efficiency

show umts-iub efficiency

To display history of the UMTS interface efficiency averages at 1 second, 5 seconds, 1 minute, 5 
minutes, and 1 hour intervals, use the 

show umts-iub efficiency 

command in privileged EXEC mode. 

Efficiency is defined as the percentage of bandwidth savings obtained by using the 
compression/decompression algorithm to suppress GSM data.

show umts-iub efficiency

 [

history

]

Syntax Description

Command Modes

Privileged EXEC

Command History

Examples

The following is an example of the output generated by this command.

Router# show umts eff

Router# show umts efficiency atm 0/0/1

UMTS(ATM0/0/1): efficiency (1sec/5sec/1min/5min/1hr) units(%%)

   decompression efficiency (100/100/100/100/---)

     compression efficiency (100/100/100/100/---)

Related Commands

history

Creates a graph display of the efficiency.

Release

Modification

12.4(2)MR

This command was introduced.

Command

Description

clear umts-iub

Clears the statistics displayed.

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments