manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 181 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 181

       

A-49

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    ipran-mib backhaul-notify-interval

ipran-mib backhaul-notify-interval

Use the 

ipran-mib backhaul-notify-interval

 command in the global configuration mode to specify the 

interval used to suppress the generation of the ciscoIpRanBackHaulRcvdUtil and the 
ciscoIpRanBackHaulSentUtil notifications from the CISCO-IP-RAN-BACKHAUL-MIB.

To set the interval used to suppress notifications, use the following configuration command or the 

no

 

form of this command to remove the interval:

ipran-mib backhaul-notify-interval 

60-900 seconds

Notifications are suppressed for the number of seconds specified. Notifications are not suppressed when 
this keyword is set to zero. The minimum interval is one minute and the maximum is fifteen minutes. 
When suppression is enabled, notifications are generated when a worse state is encountered. For 
example, the following transitions generate notifications:

  •

“acceptable” to “warning”

  •

“warning” to “overloaded”

Later transitions to lesser states are suppressed. For example, the following transitions do not generate 
notifications:

  •

“warning” to “acceptable”

  •

“overloaded” to “warning”

  •

“overloaded” to “acceptable”

At the end of the specified interval, a notification is generated if the current state is different from the 
state reported by the last notification.

Syntax Description

Defaults

Defaults to 0 (notifications are not suppressed).

Command Modes

Interface configuration

Command History

Examples

Router# 

config t

Router(config)#

 

ipran-mib backhaul-notify-interval 60

Router(config)#

 

ipran-mib backhaul-notify-interval 900

Router(config)#

 

no ipran-mib backhaul-notify-interval

Router(config)# 

exit

ipran-mib 
backhaul-notify-interval 

60-900 seconds

Release

Modification

12.4(2)MR1

This command was introduced. 

12.4(9)MR

Support for utilization notification was removed. This command is supported to 
maintain compatibility. 

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments