Cisco 3825 Series Software Configuration Manual Download Page 225

Page: 225 / 358

A-93

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

show l2tp tunnel

To display basic information about all L2TP tunnels, use the

show l2tp tunnel

command in the user

EXEC mode.

show l2tp tunnel

Syntax Description

This command has no arguments or keywords.

Command Modes

User EXEC

Command History

Usage Guidelines

Use the

show l2tp tunnel

command to display information about all active tunnels using L2TP.

Examples

The following is sample output from the

show l2tp tunnel

command on a device with active L2F and

L2TP tunnels:

Router#

show l2tp tunnel

L2TP Tunnel Information Total tunnels 1 sessions 4

LocID RemID Remote Name State Remote Address Port Sessions L2TP Class/

VPDN Group

2220 55756 mwr2 est 99.99.99.99 0 4 l2tp_default_cl

Router#

Related Commands

Release

Modification

11.2

This command was integrated into Cisco IOS Release 12.4(12)MR2.

12.1(1)T

This command was enhanced to display Point-to-Point Protocol over
Ethernet (PPPoE) information.

12.1(2)T

This command was enhanced to display PPPoE session information on
actual Ethernet interfaces.

12.4(12)MR2

This command was integrated into Cisco IOS Release 12.4(12)MR2.

Command

Description

show l2tp domain

Displays all VPDN domains and DNIS groups configured on the
network access server (NAS).

show l2tp group

Displays a summary of the relationships among VPDN groups and
customer/VPDN profiles, or summarizes the configuration of a VPDN
group including DNIS/domain, load sharing information and current
session information.

show l2tp history failure

Displays the content of the failure history table.

Summary of Contents for 3825 Series







































































































































































































































































































































































Search results

Summary of Contents for 3825 Series

Reviews:

Cisco 3825 Series, Software Configuration Manual, Page: 225 / 358

Search results

Summary of Contents for 3825 Series

Reviews: