manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 137 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 137

       

A-5

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    atm umts-iub

atm umts-iub

To select an ATM interface for UMTS Iub traffic, use the 

atm umts-iub 

Interface configuration 

command.

atm umts-iub 

Syntax Description

This command has no arguments or keywords.

Command Modes

Sub-Interface configuration

Command History

Examples

The following example illustrates the use of 

atm umts

 command.

Router(config)# 

interface ATM0/2/0

Router(config-if)# 

atm umts-iub

Release

Modification

12.4(4)MR

This command is introduced.

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments