manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 233 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 233

       

A-101

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    show redundancy

 LISTN_LISTN     Mar 19 10:20:49.299

 

 LISTN_SPEAK     Mar 19 10:20:52.244

 

 SPEAK_SPEAK     Mar 19 10:20:52.300

 

 SPEAK_STDBY     Mar 19 10:20:55.244

 

 STDBY_STDBY     Mar 19 10:20:55.300

 

 ACTIV_STDBY     Mar 19 10:21:01.692

 

 ACTIV_ACTIV     Mar 19 10:21:01.692

 

Related Commands

Command

Description

mode y-cable

Invokes y-cable mode.

redundancy

Invokes redundancy mode.

standalone

Specifies whether the Cisco 3825 router is used in a redundant or 
standalone configuration.

standby

Sets HSRP attributes.

standby use-interface

Specifies the interfaces to be used for health and revertive interfaces.

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments