Cisco 3825 Series Software Configuration Manual Download Page 246

Page: 246 / 358

A-114

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

show xconnect all

The following example shows

show xconnect al

l command output in the detailed display format:

Router#

show xconnect all detail

Legend: XC ST=Xconnect State, S1=Segment1 State, S2=Segment2 State

UP=Up, DN=Down, AD=Admin Down, IA=Inactive, NH=No HardwareXC

ST Segment 1 S1 Segment 2 S2

------+---------------------------------+--+---------------------------------+--

UP ac Et0/0(Ethernet) UP mpls 10.55.55.2:1000 UP

Interworking: ip Local VC label 16

Remote VC label 16

pw-class: mpls-ip

UP ac Et1/0.1:200(Eth VLAN) UP mpls 10.55.55.2:5200 UP

Interworking: ip Local VC label 17

Remote VC label 20

pw-class: mpls-ip

IA pri ac Et1/0.2:100(Eth VLAN) UP ac Et2/0.2:100(Eth VLAN) UP

Interworking: none Interworking: none

UP sec ac Et1/0.2:100(Eth VLAN) UP mpls 10.55.55.3:1101 UP

Interworking: none Local VC label 23

Remote VC label 17

pw-class: mpls

The additional fields displayed in the detailed output are self-explanatory.

Related Commands

State of the segment. Valid states are:

•

UP—The segment is up.

•

DN—The segment is down.

•

AD—The segment is administratively down.

Table A-6

show xconnect all Field Descriptions (continued)

Field

Description

Command

Description

show atm pvc

Displays all ATM PVCs and traffic information.

show atm vc

Displays all ATM PVCs and SVCs and traffic information.

show atm vp

Displays the statistics for all VPs on an interface or for a specific VP.

show connect

Displays configuration information about drop-and-insert
connections that have been configured on a router.

show frame-relay pvc

Displays statistics about PVCs for Frame Relay interfaces.

show interfaces

Displays statistics for all interfaces configured on the router or access
server.

show l2tun session

Displays the current state of Layer 2 sessions and protocol
information about L2TP control channels.

show mpls l2transport
binding

Displays VC label binding information.

show mpls l2transport vc

Displays information about AToM VCs that have been enabled to
route Layer 2 packets on a router.

Summary of Contents for 3825 Series







































































































































































































































































































































































Search results

Summary of Contents for 3825 Series

Reviews:

Cisco 3825 Series, Software Configuration Manual, Page: 246 / 358

Search results

Summary of Contents for 3825 Series

Reviews: