manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 267 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 267

       

A-135

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    xconnect

The 

xconnect

 command with keyword 

ignore-vpi-vci 

results in the PVC mapping being done in a 

cooperative way if the MWR works the same way as the receiving router. Without this command, the 
MWR checks the VPI/VCI value inside PW packet for matches against the local configured PVC or 
PVC-mapping. With the 

ignore-vpi-vci 

keyword configured, the MWR ignores the VPI/VCI header 

inside the received PW packet and does a blind rewrite with the local configured AC-side PVC's 
VPI/VCI value. 

Note

This applies only to N:1 VCC PW with N=1 special case.

Examples

The following example illustrates the configured 

xconnect

 service for an ATM interface by binding the 

ATM circuit to the PW named 123 with a remote peer 10.0.3.201. The configuration settings in the 
pseudowire-class named ATM-xconnect are used.

Router# 

config t

Router(config)# 

interface ATM 0/0/0

Router(config-if)# 

xconnect 10.0.3.201 123 pw-class ATM-xconnect

Router(config-if-xconn)# 

exit

Router(config-if)# 

exit

Router(config)# 

exit

The following example illustrates PVC mapping using the keyword 

ignore-vpi-vci

 with the 

xconnect

 

command. The example shows both the MWR and remote end (7600) routers. 

MWR:

Router# 

config t

Router(config)# 

interface ATM 0/0

Router(config-if)# 

pvc 0/10 12transport

Router(config-if-atm-12trans-pvc)# 

encapsulation aa10

Router(config-if-atm-12trans-pvc)# 

xconnect 10.10.10.10 100 encapsulation mpls ignore-vpi-vci

Router(config-if-atm-12trans-pvc-xconn)# 

exit

Router(config-if-atm-12trans-pvc)# 

exit

Router(config-if)# 

exit

Router(config)# 

exit

7600:

Router# 

config t

Router(config)# 

interface ATM 0/0

Router(config-if)# 

pvc 2/20 12transport

Router(config-if-atm-12trans-pvc)# 

encapsulation aa10

Router(config-if-atm-12trans-pvc)# 

xconnect 20.20.20.20 100 encapsulation mpls

Router(config-if-atm-12trans-pvc-xconn)# 

exit

Router(config-if-atm-12trans-pvc)# 

exit

Router(config-if)# 

exit

Router(config)# 

exit

Related Commands

Command

Description

show xconnect 

Displays information about xconnect attachment circuits and PWs.

pseudowire-class

 

Configures a template of PW configuration settings used by the 
attachment circuits transported over a PW. 

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments