manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 39 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 39

       

1-29

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Chapter 1      Overview of the Cisco 3825 Mobile Wireless Edge Router

    New Features in Cisco IOS Release 12.4(16)MR

 umts-iub set peering dscp 8

 umts-iub local 20.20.20.21 6666

 umts-iub remote 20.20.20.20 6666

One new CLI Show command 

show umts congestion

 

atm

 

slot/port 

has been added to this feature and 

a new field has been added to the 

show umts-iub peering

 command (see 

Appendix A, 

“Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference”

). 

The following example illustrates the use of 

show umts congestion atm

.

Router# 

show umts congestion atm 0/ima0

UMTS-Iub(ATM0/IMA0):

   Congestion: ON

   Throttled ATM cells: 415801

   Last congestion time: Mar 13 18:09:49.858   duration: 0h 0m 53s

The following example illustrates the use of 

show

 

atm umts-iub peering 

command with the new 

Congestion Control status field. In this example, it shows it On.

Router# 

show umts-iub peering atm 0/ima0

UMTS-Iub(ATM0/IMA0): Peering Information

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):       Local (20.20.20.21:6666) States:

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):            Connect State: OPEN    

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):            Redundancy State: ACTIVE

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):            Congestion Control: ON

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):            Version: 4

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):            Alarm State: 

UMTS-Iub(ATM0/0 - ATM0/2):                    RX(NO ALARM)       TX(NO ALARM)

UMTS-Iub(ATM0/1 - ATM0/3):                    RX(NO ALARM)       TX(NO ALARM)

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):       Remote (20.20.20.20:6666) States:

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):            Version: 4

UMTS-Iub(ATM0/IMA0 - ATM0/IMA1):            Alarm State: 

UMTS-Iub(ATM0/0 - ATM0/2):                    RX(NO ALARM)       TX(NO ALARM)

UMTS-Iub(ATM0/1 - ATM0/3):                    RX(NO ALARM)       TX(NO ALARM)

Inverse Multiplexing over ATM (IMA)

Inverse Multiplexing over ATM (IMA) interface as a shorthaul enables you to configure existing UMTS 
commands on IMA interfaces. No new commands are added for this new feature. Only previously 
existing Cisco IOS commands have been added for this feature (see the 

“Configuring Inverse 

Multiplexing over ATM (IMA)” section on page 4-37

 and 

Appendix A, “Cisco 3825 Mobile Wireless 

Edge Router RAN-O Command Reference”

).

When operating in the IMA environment, a sample ATM configuration is written as follows:

interface ATM0/0/0

no ip address

no atm ilmi-keepalive

ima-group 0

scrambling-payload

interface ATM0/0/1

no ip address

no atm ilmi-keepalive

ima-group 0

scrambling-payload

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments