manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 178 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 178

       

A-46

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    ip tcp header-compression

Related Commands

Command

Description

ip tcp 
compression-connections

Specifies the total number of TCP header compression connections 
that can exist on an interface.

show ip tcp 
header-compression

Displays TCP header compression statistics.

show running-config

Displays the contents of the currently running configuration file or the 
configuration for a specific interface, or map class information.

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments