manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 187 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 187

       

A-55

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    ipran-mib threshold-warning

ipran-mib threshold-warning

Use the 

ipran-mib threshold-warning

 command in the global configuration mode to specify a level of 

traffic where the instances of the cirbhBackHaulRcvdUtilState and cirbhBackHaulSentUtilState objects 
are marked as “warning.”

All changes to this threshold take affect at the end of the current interval. The value for this object must 
be greater than the value specified for the 

ipran-mib threshold-acceptable

 command keyword.

Also, the value for this object must be less than or equal to value of the 
cirbhBackHaulOverloadedThreshold object. This parameter corresponds to the 
cirbhBackHaulWarningThreshold object.

ipran-mib threshold-warning 

[30-100 Utilization default (percent)]

Syntax Description

Defaults

70 percent.

Command Modes

Interface configuration

Command History

Examples

Router# 

config t

Router(config)#

 

ipran-mib threshold-warning 60

Router(config)#

 

ipran-mib threshold-warning 80

Router(config)#

 

no ipran-mib threshold-warning

Router(config)# 

exit

Related Commands

ipran-mib 
threshold-warning

ipran-mib threshold-warning percent

Release

Modification

12.4(2)MR1

This command was introduced. 

12.4(9)MR

Support for utilization notification was removed. This command is supported to 
maintain compatibility. 

Command

Description

ipran-mib 
threshold-acceptable

Specifies the acceptable level of traffic.

ipran-mib 
threshold-overloaded

Specifies the amount of traffic that indicates the backhaul is 
overloaded.

ipran-mib 
backhaul-notify-interval

Specifies the interval used to suppress the generation of utilization 
notifications.

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments