manualshive.com logo in svg

Cisco 3825 Series, Software Configuration Manual, Page: 254 / 358

Share
Download
Cisco 3825 Series Software Configuration Manual Download Page 254

       

A-122

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

OL-15667-03

Appendix A      Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

    umts-iub backhaul-oam

umts-iub backhaul-oam

To configure the local parameters required to provide OAM cells received on the UMTS ATM interface 
to be sent across the backhaul, use the 

umts-iub backhaul-oam 

Interface configuration command. To 

not transport the OAM cells across the backhaul, use the 

no

 form of this command. 

Note

When using the 

no

 form of the command, the end devices may only use OAM loopback cells. I.610 OAM 

messages are not supported by the Cisco 3825 router; therefore, if you are using this mode, OAM cells 
should be backhauled.

 

 

Additionally, the 

pvc-oam manage

 Interface configuration for ATM-VC commands at the PVC 

configuration level should be enabled for UMTS PVCs on the Cisco 3825 router. These PVCs will 
respond to OAM cells if the no version of the 

umts-iub backhaul-oam

 command is used.

umts-iub backhaul-oam

Syntax Description

This command has no arguments or keywords.

Defaults

There are no default settings or behaviors.

Command Modes

Interface configuration

Command History

Examples

The following example shows how to configure the local parameters:

Router(config)# 

interface ATM0/2/0

Router(config-if) 

atm umts-iub

Router(config-if) 

umts-iub local 10.10.10.2 5504

Router(config-if) 

umts-iub backhaul-oam

Release

Modification

12.4(2)MR

This command was introduced.

Summary of Contents for 3825 Series







































































































































































































































































































































































Reviews:

No comments