Rev Z
Page 54
11/28/2011
Copyright © 2011 by Cirus Controls, LLC. All Rights Reserved. No part of this material may be reproduced without the express
written permission of Cirus Controls LLC for each reproduction.
Spinner Always On (obsolete):
no longer functional, will be removed in future designs.
Zero velocity Overdrive
: allows Zero velocity to run slightly slower (neg.) or faster (pos) than truck speed.
Zero velocity Pulses Per Revolution
: Sensor signal pulses/rev. Default is 4.0
Zero velocity Impeller Diameter
: Unique value for a given Zero velocity system (inches).
Spinner Advanced Settings
Lock Strength
: Set at 0 and do not adjust.
Lock Increment:
SpreadSmart Rx PWM response increment. Set at 70 (no units). Increasing value causes spreader
to attempt to correct more frequently causing display to be more jumpy.
Update Laps
: Feedback adjustment response cycle rate. Allows coil to react. Set at 3 cycles. Increasing value makes
controller respond more slowly, decreasing makes controller respond more rapidly.
Unseat Drive Percent
: % of trim signal used to unseat valve at motion startup. Set at 50% typically.
Unseat Time
: Length of time that unseat signal is sent. Set at 10 (1 equals one
tenth of second).
Prewet Settings
Device Present
: select yes or no to tell the controller that an pre-wet pump is present.
Device Has Sensor
: select yes or no to tell the controller that a pre-wet sensor is present.
Minimum Trim PWM
: PWM value when Prewet pump starts pumping. Value determined at “trim” step.
Minimum Trim PPM
: Pulse per minute value received from flow sensor with Prewet system running at min. trim.
Maximum Trim PWM
: PWM value when pre-wet pump hits max output. Value determined at “trim”
Maximum
Trim PPM
: Pulse per minute value received from flow sensor when Prewet system is running at maximum trim.
Pulses Per Gallon
: Input value from the flow meter on the pre-wet system. Key conversion factor.
Pump Max. Gallon/Minute
: Input value from the pre-wet pump rating. Limit of open loop output.
Pre-Wet Advanced Settings
Lock Strength
: Set at 0 and do not adjust.
Lock Increment:
SpreadSmart Rx PWM response increment. Set at 70 (no units). Increasing value causes spreader
to attempt to correct more frequently causing display to be more jumpy.
Update Laps
: Feedback adjustment response cycle rate. Allows coil to react. Set at 3 cycles. Increasing value makes
controller respond more slowly, decreasing makes controller respond more rapidly.
Unseat Drive Percent
: % of trim signal used to unseat valve at startup. Set at 50% (To unseat sticky valves)
Unseat Time
: Length of time that unseat signal is sent. Set at 10 (1 equals 0.1 second).
Anti-Ice Settings:
Device Present
: select yes or no to tell the controller that an Anti-Ice pump is present.
Device Has Sensor
: select yes or no to tell the controller that an Anti-Ice sensor is present.
Minimum Trim PWM
: PWM value when anti-ice pump starts pumping. Value determined at “trim” step
Minimum
Trim PPM
: Pulse per minute value received from flow sensor when Anti-Ice system is running at minimum trim.
Maximum Trim PWM
: PWM value at anti-ice pump max output. Value determined at “trim” step.
Maximum Trim
PPM
: Pulse per minute value received from Anti-Ice liquid flow sensor when Anti-Ice system is running at max. trim.
Pulses Per Gallon
: Input value from the flow meter on the anti-ice system. Key conversion factor.
Pump Max. Gallon/Minute
: Input value from the anti-ice pump. Limit of open loop output.
Tier 1 Gallon/Minute
: Maximum flow rate of the Tier 1 booms (in gallons per minute)
Tier 2 Gallon/Minute
: Maximum flow rate of the Tier 2 booms (in gallons per minute).
Anti-Ice Advanced Settings
Lock Strength
: Set at 0 and do not adjust.
Lock Increment:
SpreadSmart Rx PWM response increment. Set at 70 (no units). Increasing value causes spreader
to attempt to correct more frequently causing display to be more jumpy.
Update Laps
: Feedback adjustment response cycle rate. Allows coil to react. Set at 3 cycles. Increasing value makes
controller respond more slowly, decreasing makes controller respond more rapidly.
Unseat Drive Percent
: % of trim signal used to unseat valve at motion startup. Set at 50% (to unseat sticky valves);
Unseat Time
: Length of time that unseat signal is sent. Set at 10 (1 equals one
tenth of second).
Speedometer Calibration – part of “Trim/Cal Menu”
Speedo Setting
: Pulses Per Mile traveled. Value determined during Speedo Trim step.
