manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 344 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 344

3. Remove the protective cover over the remote positive

(+)

battery post. To remove the cover, press the locking

tab and pull upward on the cover.

4. If using a another vehicle to jump-start the battery,
park the vehicle within the jumper cables reach, set the
parking brake and make sure the ignition is OFF.

WARNING!

Do not allow vehicles to touch each other as this
could establish a ground connection and personal
injury could result.

Jump-Starting Procedure

WARNING!

Failure to follow this procedure could result in per-
sonal injury or property damage due to battery ex-
plosion.

CAUTION!

Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
or the discharged vehicle.

Locking Tab

6

WHAT TO DO IN EMERGENCIES

343

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments