manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 336 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 336

Preparations For Jacking

1. Park the vehicle on a firm, level surface. Avoid ice or
slippery areas.

WARNING!

Do not attempt to change a tire on the side of the
vehicle close to moving traffic. Pull far enough off
the road to avoid the danger of being hit when
operating the jack or changing the wheel.

2. Set the parking brake.

3. Place the shift lever into PARK (automatic transaxle)
or REVERSE (manual transaxle).

4. Turn OFF the ignition.

5. Turn on the Hazard Warning flasher.

6. Block both the front and rear of the
wheel diagonally opposite the jacking
position. For example, if changing the
right front tire, block the left rear
wheel.

NOTE:

Passengers should not remain in the vehicle

while the vehicle is being jacked.

6

WHAT TO DO IN EMERGENCIES

335

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments