manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 28 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 28

1. With the RKE transmitter buttons facing down, use a
flat blade to pry the two halves of the RKE transmitter
apart. Make sure not to damage the seal during removal.

2. Remove and replace the battery. Avoid touching the
new battery with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.

3. To assemble the RKE transmitter case, snap the two
halves together.

General Information

This device complies with part 15 of FCC rules and with
RS-210 of Industry Canada. Operation is subject to the
following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference that may be
received including interference that may cause undesired
operation.

NOTE:

Changes or modifications not expressly ap-

proved by the party responsible for compliance could
void the user’s authority to operate the equipment.

Separating RKE Transmitter Halves

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

27

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments