Home
/
Chrysler
/
2010 Sebring
/
Owner'S Manual

Chrysler 2010 Sebring, Owner'S Manual, Page: 107 / 456

Share

Page: 107 / 456

Chrysler 2010 Sebring Owner'S Manual Download Page 107

The hard seatback features a work surface and a molded
rim for retaining items stored on the seatback panel.

Folding Rear Seat

To provide additional storage area, the rear seatback can
be folded forward. Pull on the loops shown in the picture
to fold down either or both seatbacks.

When returning the rear seatback to the upright position,
be sure the seatback is latched.

Fold-Flat Front Passenger Seat

Folding Rear Seats

106

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
105
106
107
108
109
...
»

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments