Home
/
Chrysler
/
2010 Sebring
/
Owner'S Manual

Chrysler 2010 Sebring, Owner'S Manual, Page: 124 / 456

Share

Page: 124 / 456

Chrysler 2010 Sebring Owner'S Manual Download Page 124

To Resume Speed

If you deactivated the Electronic Speed Control without
erasing the set speed from memory and your vehicle
speed is above 20 mph (32 km/h) you can resume the
previous set speed. To do so, push the lever up and
release RESUME ACCEL, and then remove your foot
from the accelerator pedal.

To Vary the Speed Setting

When the Electronic Speed Control is set, you can in-
crease speed by pushing up and holding the RESUME
ACCEL lever. If the lever is continually held in the
RESUME ACCEL position, the set speed will continue to
increase until the lever is released, then the new set speed
will be established.

Tapping RESUME ACCEL once will result in a 1 mph
(2 km/h) speed increase. Each time the lever is tapped,
speed increases so that tapping the lever three times will
increase speed by 3 mph (5 km/h), etc.

To decrease speed while the Electronic Speed Control is
set, push down and hold the SET DECEL lever. If the
lever is continually held in the SET DECEL position, the
set speed will continue to decrease until the lever is
released. Release the lever when the desired speed is
reached, and the new set speed will be established.

Tapping the SET DECEL lever once will result in a 1 mph
(2 km/h) speed decrease. Each time the button is tapped,
speed decreases.

WARNING!

Electronic Speed Control can be dangerous where the
system cannot maintain a constant speed. Your ve-
hicle could go too fast for the conditions, and you
could lose control. An accident could be the result.
Do not use Electronic Speed Control in heavy traffic
or on roads that are winding, icy, snow-covered, or
slippery.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

123

«
...
122
123
124
125
126
...
»

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments