manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 225 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 225

REMOTE SOUND SYSTEM CONTROLS — IF
EQUIPPED

The remote sound system controls are located on the rear
surface of the steering wheel. The left and right controls
are rocker-type switches with a pushbutton in the center
of each switch. Reach behind the steering wheel to access
the switches.

Right-Hand Switch Functions

•

Press the top of the switch to increase the volume.

•

Press the bottom of the switch to decrease the volume.

Remote Sound System Controls (Back View Of Steering

Wheel)

224

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments