Home
/
Chrysler
/
2010 Sebring
/
Owner'S Manual

Chrysler 2010 Sebring, Owner'S Manual, Page: 139 / 456

Share

Page: 139 / 456

Chrysler 2010 Sebring Owner'S Manual Download Page 139

STORAGE

Driver’s Side Sunglass Holder — If Equipped

An integrated sunglass holder is located in the headliner
above the sun visor. To access the sunglass holder, lower
the sun visor. Small items such as toll tickets can be
stored between the two straps, while sunglasses or other
items can be stored above the two straps.

Cargo Area

The 60/40 split-folding rear seat provides cargo-carrying
versatility. The seatbacks fold down easily by pulling
nylon tabs between the seatbacks and the bolsters. When
the seats are folded down, they provide a continuous,
nearly flat extension of the load floor.

Sunglass Holder

138

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
137
138
139
140
141
...
»

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments