manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 262 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 262

WARNING!

•

Driving through standing water limits your vehi-
cle’s traction capabilities. Do not exceed 5 mph
(8 km/h) when driving through standing water.

•

Driving through standing water limits your vehi-
cle’s braking capabilities, which increases stop-
ping distances. Therefore, after driving through
standing water, drive slowly and lightly press on
the brake pedal several times to dry the brakes.

•

Getting water inside your vehicle’s engine can
cause it to lock up and stall out, and leave you
stranded.

•

Failure to follow these warnings may result in
injuries that are serious or fatal to you, your
passengers, and others around you.

POWER STEERING

The standard power steering system will give you good
vehicle response and increased ease of maneuverability
in tight spaces. The system will provide mechanical
steering capability if power assist is lost.

If for some reason the power assist is interrupted, it will
still be possible to steer your vehicle. Under these condi-
tions, you will observe a substantial increase in steering
effort, especially at very low vehicle speeds and during
parking maneuvers.

NOTE:

•

Increased noise levels at the end of the steering wheel
travel are considered normal and do not indicate that
there is a problem with the power steering system.

•

Upon initial start-up in cold weather, the power steer-
ing pump may make noise for a short amount of time.
This is due to the cold, thick fluid in the steering

5

STARTING AND OPERATING

261

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments