manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 324 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 324

Trailer and Tongue Weight

Always load a trailer with 60% to 65% of the weight in
the front of the trailer. This places 10% of the Gross Trailer
Weight (GTW) on the tow hitch of your vehicle. Loads
balanced over the wheels or heavier in the rear can cause
the trailer to sway

severely

side to side which will cause

loss of control of vehicle and trailer. Failure to load
trailers heavier in front is the cause of many trailer
accidents.

Never exceed the maximum trailer tongue weight
stamped on your bumper or trailer hitch.

Consider the following items when computing the
weight on the rear axle of the vehicle:

•

The trailer tongue weight of the trailer.

•

The weight of any other type of cargo or equipment
put in or on your vehicle.

•

The weight of the driver and all passengers.

5

STARTING AND OPERATING

323

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments