manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 342 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 342

JUMP-STARTING

If your vehicle has a discharged battery it can be jump-
started using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack

follow the manufacturer’s operating instructions and
precautions.

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

WARNING!

When temperatures are below the freezing point,
electrolyte in a discharged battery may freeze. Do not
attempt jump-starting because the battery could rup-
ture or explode and cause personal injury. Battery
temperature must be brought above the freezing
point before attempting a jump-start.

6

WHAT TO DO IN EMERGENCIES

341

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments