manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 333 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 333

HAZARD WARNING FLASHER

The Hazard Warning flasher switch is located on the
instrument panel, below the radio.

Press the switch to turn on the Hazard Warning
flasher. When the switch is activated, all directional
turn signals will flash on and off to warn oncoming

traffic of an emergency. Press the switch a second time to
turn off the Hazard Warning flasher.

This is an emergency warning system and should not be
used when the vehicle is in motion. Use it when your
vehicle is disabled and is creating a safety hazard for
other motorists.

If it is necessary to leave the vehicle to go for service, the
Hazard Warning flasher will continue to operate with the
ignition key removed and the vehicle locked.

NOTE:

With extended use, the Hazard Warning flasher

may wear down your battery.

IF YOUR ENGINE OVERHEATS

In any of the following situations, you can reduce the
potential for overheating by taking the appropriate ac-
tion.

•

On the highways — Slow down.

•

In city traffic — While stopped, put transaxle in
NEUTRAL, but do not increase engine idle speed.

CAUTION!

Driving with a hot cooling system could damage
your vehicle. If temperature gauge reads “H”, pull
over and stop the vehicle with the engine at idle,
when safe. Turn the air conditioner off and wait until
the pointer drops back into the normal range. After
appropriate action has been taken, if the pointer
remains on the “H”, turn the engine off immediately,
and call for service.

332

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments