manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 120 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 120

WARNING!

Sudden loss of visibility through the windshield
could lead to an accident. You might not see other
vehicles or other obstacles. To avoid sudden icing of
the windshield during freezing weather, warm the
windshield with defroster before and during wind-
shield washer use.

Mist Feature

Push down on the wiper control lever to activate a single
wipe to clear the windshield of road mist or spray from
a passing vehicle. As long as the lever is held down, the
wipers will continue to operate.

Headlights With Wipers Feature (Available With
Automatic Headlights Only)

When this feature is active, the headlights will turn on
approximately 10 seconds after the wipers are turned on
if the multifunction lever (on the left side of the steering

Mist Control

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

119

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments