manualshive.com logo in svg

Chrysler 2010 Sebring, Owner'S Manual, Page: 249 / 456

Share
Download
Chrysler 2010 Sebring Owner'S Manual Download Page 249

CAUTION!

To prevent damage to the starter, wait 10 to 15 sec-
onds before trying again.

After Starting

The idle speed will automatically decrease as the engine
warms up.

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.

The engine block heater cord is bundled under the hood
between the headlight assembly and the Totally Inte-
grated Power Module (Fuse Box) on the driver’s side of
the vehicle.

WARNING!

Remember to disconnect the cord before driving.
Damage to the 110-115 Volt electrical cord could cause
electrocution.

AUTOMATIC TRANSAXLE

CAUTION!

Damage to the transaxle may occur if the following
precautions are not observed:

•

Shift the shift lever into PARK only after the
vehicle has come to a complete stop.

(Continued)

248

STARTING AND OPERATING

Summary of Contents for 2010 Sebring









































































































































































































































































































































































































































































Reviews:

No comments