manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 90 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 90

DRIVER MEMORY SEAT — IF EQUIPPED

This feature allows the driver to store up to two different
memory profiles, for easy recall through a memory
switch. Each memory profile contains desired position
settings for the driver seat, side mirror, adjustable pedals,
and power tilt and telescopic steering column, and a set
of desired radio station presets.

The memory switch is located on the driver’s door panel.
The switch contains an (S) button to activate the memory
save function. It also contains a rocker switch labeled
with the number (1) and the number (2). The rocker
switch allows the driver to recall either of two pre-
programmed memory profiles by pressing the appropri-
ate side of the switch.

Programming The Memory Feature

To create a new memory profile, perform the following:

NOTE:

Saving a new memory profile will erase an

existing profile from memory.

1. Adjust all memory profile settings to desired prefer-
ences (i.e. seat, side mirror, adjustable pedals, power tilt
and telescopic steering column, and radio station pre-
sets).

Memory Switch

90

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments