Home
/
Chrysler
/
2007 300 SRT8
/
Owner'S Manual

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 183 / 360

Share

Page: 183 / 360

Chrysler 2007 300 SRT8 Owner'S Manual Download Page 183

RADIO OPERATION AND CELLULAR PHONES

Under certain conditions, the cellular phone being On in
your vehicle can cause erratic or noisy performance from
your radio. This condition may be lessened or eliminated
by relocating the cellular phone antenna. This condition
is not harmful to the radio. If your radio performance
does not satisfactorily “clear” by the repositioning of the
antenna, it is recommended that the radio volume be
turned down or off during cellular phone operation.

CLIMATE CONTROLS

The Air Conditioning and Heating System is designed to
make you comfortable in all types of weather.

Automatic Temperature Control

Automatic Operation

The Infrared Dual-Zone Climate Control System auto-
matically maintains the climate in the cabin of the vehicle
at the comfort levels desired by the driver and passenger.
To accomplish this, the system gathers information from
the controls on the climate control, from a dual sun-
sensor located in the top of the instrument panel, from an
infrared sensor located in the face of the climate control,
and from various sensors located throughout the vehicle.

Automatic Temperature Controls

UNDERSTANDING YOUR INSTRUMENT PANEL

183

4

«
...
181
182
183
184
185
...
»

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments