manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 199 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 199

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms engine coolant and
permits quicker starts in cold weather. Connect the cord
to a standard 110-115 volt AC electrical outlet with a
grounded, three-wire extension cord.

The engine block heater cord is routed under the hood on
the driver side of the vehicle. It has a removable cap that
is located on the driver side of the Integrated Power
Module.

WARNING!

Remember to disconnect the cord before driving.
Damage to the 110-115 volt electrical cord could
cause electrocution.

AUTOMATIC TRANSMISSION

CAUTION!

Damage to the transmission may occur if the follow-
ing precautions are not observed:

•

Shift into PARK only after the vehicle has come to
a complete stop.

•

Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the
engine is at idle speed.

•

Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed.

•

Before shifting into any gear, make sure your foot
is firmly on the brake pedal.

STARTING AND OPERATING

199

5

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments