Chrysler 2007 300 SRT8 Owner'S Manual Download Page 121

Page: 121 / 360

For questions or comments, contact HomeLink at

www.homelink.com or 1-800-355-3515

Security

If you sell your vehicle, be sure to erase the frequencies
by following the “Erasing HomeLink Buttons” instruc-
tions in this section.

This device complies with part 15 of FCC rules and with
RSS-210 of Industry Canada. Operation is subject to the
following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference that may be
received including interference that may cause undes-
ired operation.

NOTE:

Changes or modifications not expressly ap-

proved by the party responsible for compliance could
void the user’s authority to operate the equipment.

HomeLink

威

is a trademark owned by Johnson Controls,

Inc.

POWER SUNROOF — IF EQUIPPED

The power sunroof switch is located between the sun
visors on the overhead console.

Power Sunroof Controls

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

121

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Search results

Summary of Contents for 2007 300 SRT8

Reviews:

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 121 / 360

Search results

Summary of Contents for 2007 300 SRT8

Reviews: