manualshive.com logo in svg

Chrysler 2007 300 SRT8, Owner'S Manual, Page: 13 / 360

Share
Download
Chrysler 2007 300 SRT8 Owner'S Manual Download Page 13

NOTE:

A key, which has not been programmed, is also

considered an invalid key even if it is cut to fit the
ignition lock cylinder for that vehicle.

During normal operation, after turning on the ignition
switch, the Vehicle Security Alarm Indicator Light will
turn on for three (3) seconds for a bulb check. If the light
remains on after the bulb check, it indicates that there is
a problem with the electronics. In addition, if the light
begins to flash after the bulb check, it indicates that
someone used an invalid key to start the engine. Either of
these conditions will result in the engine being shut off
after two (2) seconds.

If the Vehicle Security Alarm Indicator Light turns on
during normal vehicle operation (vehicle running for
longer than 10 seconds), it indicates that there is a fault in
the electronics. Should this occur, have the vehicle ser-
viced as soon as possible.

NOTE:

•

The Sentry Key Immobilizer System is not compatible
with remote starting systems. Use of these systems
may result in vehicle starting problems and loss of
security protection.

•

Exxon/Mobil Speed Pass,™ additional Sentry Keys, or
any other transponder-equipped components on the
same key chain will

not

cause a key-related (tran-

sponder) fault unless the additional part is

physi-

cally held against the ignition key

being used

when starting the vehicle. Cell phones, pagers, or
other RF electronics will not cause interference with
this system.

All of the keys provided with your new vehicle have
been programmed to the vehicle electronics.

Replacement Keys

NOTE:

Only keys that are programmed to the vehicle

electronics can be used to start and operate the vehicle.
Once a Sentry Key is programmed to a vehicle, it cannot
be programmed to any other vehicle.

At the time of purchase, the original owner is provided
with a four-digit PIN number. This number is required
for dealer replacement of keys. Duplication of keys may
be performed at an authorized dealer or by using the
Customer Key Programming procedure. This procedure

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

13

2

Summary of Contents for 2007 300 SRT8









































































































































































































































































































































































Reviews:

No comments